Review: Dead-On Annililator 18inch Superhammer

As first seen on BreachBangClear,  and now on to you.

I wanted to get a full-on gift for a friend, one of the fantastic Dead-On Annihilator superhammers and due to a failure to read the details on my part, I accidentally ordered the 18" version, not the 14" version, like the one I already had. To make things right, I simply gave my friend the 14" he was already trialling, and kept the monstrous 18" for myself. It really is a beast.

Probably too much tool for most people, at 1.9kg (3.7lbs) and 30cm (12") shaft with a 45cm (18") overall length. All the features of the 14" are replicated in the 18", just "bigger".
Between the striking face and the "Nail Puller" the "Board Straightener" sits ready to grip and twist.

The two sets of teeth are just over 4cm (1 5/8") and just under 3cm (1 1/8") in width, respectively, which fits standard board sizes for wrenching or adjusting.To be honest, I haven't had much use for this other than occasionally levering at a frame here or there. The hammer is good though, the face is wide and beveled giving both a good nail-driving action, without messing up the surface you're pounding on.

Below the chisel edged Nail Puller/Tile Ripper lies the frightfully formed Demolition Axe, which curves down almost to the edge of the rubberised grip. This is not a shaving-sharp axe, rather that the steel of the haft is formed to a triangular ridge to an angle of around 45 degrees to the full width of the haft. This leaves a very hardy working edge, and is intended for drywall, thin wooden structures, shingles and conduit.

The drywall-only labeled demolition axe seems to work well on particle board, and would probably make short work of errant wrists too. 

The middle of the curve is notched with what appears to be a wire-stripper, but could also be used as a nail-puller as well. As the 18" version is just a heftier version of the 14", the angles are steeper, so it's not really sharp at all, but it is wicked solid. I can imagine that the warning is there for the same reason that coffee lids read "Caution: contents hot". For idiots who try to chop wood, or cut wiring with it. It wont do that, or at least, not well, or safely. Use the right tool for the job. It will make a mess of whatever you want to make a mess of though, so in that, its perfect.

The pointy-end of the tool features several other interesting combination tools. The tip is a rugged ridged point, which could be used for penetration, or scoring as needed. Within the tip is the "Multi Purpose Wrench/Nail Puller", which as suggested includes a hex-bolt socket, and a wide feeding nail puller. The head of the hammer fits nicely in the palm of the hand to drive the spike home.

 The manufacturers suggest using the wrench for releasing concrete forms and other general uses and the tip for smashing, cracking and chipping away at tile, brick or other things deemed "to go away".  I like using it to punch holes in things for old fashioned "Here's Johnny" moments. Again, it makes a mess where needed.

 So, I felt it was a good idea to put the 18" Annihilator up against the mighty Stanley Fatmax Fubar to give a good comparison. However, at 1900g vs 1300g it already comes up significantly heftier. More so again than the 800g 14" Annihilator. This is a big tool, for people with big hands and big tasks. It's probably too much tool for me.  If you're in-field and cutting back every weight counts, you might want to consider the 14" over the 18", but if you are able to keep it in a vehicle, it would be a perfect  multi-function wrecker.

They are really inexpensive, rugged and well designed. When it comes time for me to break my way into an abandoned warehouse, bust my plucky crew out of a cannibal mutants larder, or even just pop open packing crates and 44 gallon drums of fuel for the gyrocopter, the 18" Dead-On Annililator might well be the way to go.

There is also fact that Shaddox Tactical make a Tactical Pouch for it, so I'm hooked.